mklilobootForum: HD Install Topic: mkliloboot started by: genee Posted by genee on Oct. 16 2004,04:26
I boot DSL using floppy and usb flash drive. I imaged bootusb.img on floppy and copied knoppix folder of the CD to the usb flsh drive. I also partitioned hdd. I tried to install dsl on hard drive. In root, i ran dsl-hdinstall, then mkliloboot. dsl-hdinstall process was installed, but i'm getting error in mkliloboot. After dsl-hdinstall, "Do you want to run mkliloboot now? y . .. . Warning: '/proc/partitions' does not exist, disk can bypassed. Added Linux * Skipping /vmlinuz.old Device 0x800: Inconsistent partition table, 1st entry CHS address in PT:0:1:1 --> LBA (43) LBA address in PT: 5 --> CHS(0:0:6) Fatal:Either FIX-TABLE or IGNORE-TABLE must be specified . . The lilo boot installation process is finished. Renoot now? " After mkliloboot, I can't boot using hdd. ANy idea? Posted by Pengel on Oct. 23 2004,19:54
I don't know how to help you at the moment, but as I am having a very similar problem with the same error, if I find a solution I'll post it here. Hopefuly someone more knowledgeable then me will be able to help. I had no problem with dsl-hdinstall on 6.2, maybe I'll put it back on, but I haven't had any luck with 8.2. Maybe my system is just too old and underpowered:Toshiba Satellite Pro 410CDT (Laptop) Pentium 90 40M Memory 15G hd 4x cdrom ext floppy Good Luck Mike Cook Posted by AwPhuch on Oct. 24 2004,03:21
If you have multiple partitions say like a fat32 win98 partition copy the /KNOPPIX and /boot directory to that partition...then use the 0.8.0 bootfloppy image and install that way...you have to have the /boot dir or it wont install properlyBrian AwPhuch Posted by BoZ on Feb. 08 2005,20:21
Hi,I'm running into the same kind of problems. I'm also trying to hd-install form a usb-key. I added the /boot directory from cd image to solve some dsl-hdinstall errors. dsl-hd-install script is running fine but I have quite the same error than you when running mkliloboot. I have win98 on /dev/hda1, linux swap on /dev/hda2 and dsl install on /dev/hda3. I tried to use both "/dev/hda" and "/dev/hda3" when asked for the root partitions. I get error in each case. Isn't it possible to directly edit the lilo.conf that is in the /etc/ of the hd partition? Posted by IndrekSnt on Feb. 13 2005,12:23
But what if i don't have the error, but i still can't get DSL booting from hd?I have 2 hds in my 486. One is FAT32 and called hdb1 in DSL. The second is divided into 3: 1.Some kind of Compaq inspection or something (hda3) 2.Linux Swap (hda1) 3.Linux ext2 (hda2) At first i called "mkswap /dev/hda1" and then "swapon /dev/hda1" from Bash. Everything went fine: DSL started using the swap partition. Then i made the sdl-hdinstall onto hda2. No errors, nothing. I also entered "/dev/hda2" as an answer to mkliloboot's question. Only the warnings showed up that genee had reported. It made a reboot then, i removed DSL boot floppy and it started writing strange things onto the screen: L 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 and it hanged.. What did i do wrong? All suggestions are welcome, thank You.. Posted by SaidinUnleashed on Feb. 13 2005,17:45
AH! I see you got a perfect install of L 99 99 99 99 99 99 99...This happens, because Lilo sucks sometimes. You can either reinstall DSL, or, use my grub install method in the Docs. -J.P. Posted by IndrekSnt on Feb. 14 2005,14:11
Thank You, i had reinstalled it so many times that i wanted to check the forum.I used a 486 and BIOS had a hd limitation of 512MB, but i had a 900MB ext2 and a 64MB swap partition. And that was why GRUB reported: "ERROR 18 : Selected cylinder exceeds maximum supported by BIOS" and couldn't load linux24. Then i booted DSL from a floppy again, repartitioned the hd and reinstalled DSL. I then booted from GRUB, set some settings and after that installed grub from root with an accidental entry of something like this "mydsl-load grub.dsl". When finished, i changed some lines from /boot/grub/menu.lst: 1.I deleted all '#' signs that were before linux booting code 2.I changed all the settings to match the hd, where DSL was now installed After a reboot GRUB showed a menu and i was able to choose from "linux", "windows", "other". So nothing had gone wrong.. Thank You Saidin.. Posted by iduriduridur on Feb. 15 2005,00:57
The fix for this at least for me was to remove any SATA drives from my pc temporarily. They seem to break this lilo script. Once i removed them it install to hd fine. I had 2 raid 0 pairs of drives hooked up. It confused me becsue I was installing to a ide drive on /dev/hda. But i get no more 999999 at lilo coming up. I reattached after rebooting after mkliloboot my raid drives and voila IT WORKS. amd 64 k8t-neo 1 IDE 1 VIA VT4620 RAID 0 2 drives sata 1 promise RAID 0 2 drives sata |