Problems configuring LILO


Forum: HD Install
Topic: Problems configuring LILO
started by: Bidi
Posted by Bidi on Dec. 26 2004,03:01
I actually did a search and couldn't find anything remotely close to what I'm going.  First of all, I would just like to know how to configure LILO.  I tried a few different things and just can't get it to load the boot option screen.  I'm pretty sure I'm not doing it right, so if anyone can explain this to me step by step, or point me in the right direction.  Right now I have 2 partition on my HDA: DSL on hda1 and FreeDOS on hda2.

Here's what my lilo.conf looks like:
Quote

vga=791
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
#    bios=0x81

#disk=/dev/sda
#    bios=0x80

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda1

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=50

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.tx
prompt
# single-key
# delay=100
timeout=100

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
append="hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce noapic"

# Boot up Linux by default.
#
#default=Linux

image=/boot/linux24
label=Linux

read-only
# restricted
# alias=1

image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
other=/dev/hda2
label=FreeDOS
# restricted
# alias=3


Anything will help...
Posted by Bidi on Dec. 27 2004,02:02
Anyone?  Anyone at all know how to do this?  I'm sure I'm not the only one trying to run a multi-boot system.
Posted by modon on Dec. 28 2004,20:17
...... and what does Lilo answer when you run it? :;):
Posted by caulktel on Dec. 28 2004,20:38
I know this is a silly questian, but did you run lilo as root after you changed the lilo.conf file?
Posted by Bidi on Dec. 28 2004,21:55
Oh, sorry, forgot to update the post.  It turned out to be that my FreeDOS partition wasn't properly formatted for FAT16 so it wouldn't load.
Powered by Ikonboard 3.1.2a
Ikonboard © 2001 Jarvis Entertainment Group, Inc.