Wireless Cardbus Network Card
Forum: Networking
Topic: Wireless Cardbus Network Card
started by: ke4nt1
Posted by ke4nt1 on July 24 2004,02:39
For my laptop, I picked up one of these pcmcia wireless lan cards today.Plugged it in, booted DSL, and it worked...
Or so I thought.. figured I had to set the wep, but NO...
Well.. almost... Lights Up... !!!
When you bootup it shows....
cardmgr[59]: starting, version is 3.1.33
cardmgr[59]: watching 2 sockets
cardmge[59]: Card Service release does not match
cardmgr[59]: Socket 0 : PROXIM Rangelan-DS/LAN PC CARD
cardmgr[59]: executing: 'modprobe prism2_cs'
cardmgr[59]: executing: './wlan-ng start wlan0'
cardmgr[59]: + debian network setup
cardmgr[59]: + /sbin/ifup wlan0
cardmgr[59]: + ifup ignoring unknown interface wlan0
and when you shutdown .......
cardmgr[59]: executing: './wlan-ng stop wlan0'
cardmgr[59]: + /sbin/ifdown wlan0
cardmgr[59]: + ifdown: Ignoring unknown interface wlan0
cardmgr[59]: + /sbin/ifconfig wlan0 down
cardmgr[59]: executing: 'modprobe -r prism2_cs
I've searched thru the forums for some details.
Most posts tell of either great success or failure/compile driver...
Any ideas? Seems like I'm real close...
The driver is listed in dmesg as the prism2_cs irq3 io=0x0100 - 0x013f
[URL] < http://www.directron.com/rangelands.html]Proxim > RangeLAN-DS 802.11b Wireless PCMCIA[/URL]
73
ke4nt
Posted by ke4nt1 on July 24 2004,10:02
OK here is my current progress so far for this damn PROXIM RangeLAN-DS wireless card...<<"ifconfig">>
lo link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:25 erroes:0 dropped:0 overruns:0 frame:0
TX packets:25 erroes:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2800 (2.7 KiB) TX bytes:2800 (2.7 KiB)
wlan0 Link encap:UNSPEC HWaddr 00-60-xx-xx-xx-xx-00-00-00-00-00-00-00-00-00-00
inet addr:102.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9032 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:27 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:647118 (631.9 KiB) TX Bytes:) (0.0 Kib)
Interrupt:3 Base address:0x100
<<"iwconfig">>
lo no wireless extensions
Warning: Driver for device wlan0 has been compiled with version 15
of Wireless Extension, while this program is using version 16.
Some things may be broken...
wlan0 IEEE 802.11-b ESSID:"box" Nickname:"box"
Mode:Auto Frequency:2.447Ghz Access Point: 00:0F:xx:xx:xx:xx
<-- this is my mac for router, ...it found it by itself -->
Bit Rate:2Mb/s Tx-Power:-1064919200 dBm
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Link Quality:0/1 Signal Level:-90 dBm Noise level:-90 dBm
Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Surely, I'm making some good progress here.... Still no internet or pings, though...
Does any of this look either real good, or real bad ??
Any Ideas?
73
ke4nt
Posted by ke4nt1 on July 31 2004,14:18
I FINALLY got this wireless card working....<<EDIT>>
I'm guessing this will work for ANY prism2 chipset.
GIve it a try, and feecback...
<</EDIT>>
wlcardconfig just dies, it says no wireless card found.
iwconfig usually shows nothing lo - no wireless extensions
netcardconfig shows no network card found..
Using some other tools I found gave me the results posted
earlier in this thread, but no wireless connection .. Boo..
Here's what I did to get this prism2 chipset working..
type in a shell as sudo su...
"wlanctl-ng wlan0 lnxreq_ifstate ifstate=enable" <enter>
and the shell reports...
"message=lnxreq_ifstate
ifstate=enable
resultcode=success
now, type
"wlanctl-ng wlan0 lnxreq_autojoin ssid=linkkor authtype=opensystem" <enter>
and the shell reports...
"message=lnxreq_autojoin
ssid='linksys'
authtype=opensystem
resultcode=success"
Now, I go to the "netcardconfig" option in the menu,
It asks me to try DHCP, click "yes"
It reports "OK"
and I'm ONLINE .... totally unsecure, but it's a start..
WOOHOO !!
now to get the wep code in there too..
maybe add it to the last line before running netcardconfig..
YES,YES,YES.. give my creation LIFE AAAHAHAHHAA
73
ke4nt
Posted by ke4nt1 on July 31 2004,22:55
bump
Posted by Ian on Oct. 26 2004,02:31
Good Man!! I have been fighting with a 3com card which gave the same problems as your card, could be rebranded, and with two lines in the console it works!!! Thanks a ton!Ian
Posted by AwPhuch on Oct. 26 2004,16:52
Damn ke4nt1..do you ever sleepI wish my wife was as forgiving and understood my love for linux/computers like your wife does...whats your secret
Brian
AwPhuch