ADSL Conected but cat navigate
Forum: Networking
Topic: ADSL Conected but cat navigate
started by: NettoBr
Posted by NettoBr on Oct. 14 2005,14:03
Hello People,I´m impressed with DSL, its very good for my Toshiba sat. 2170 CDT, 500 MHz.
I had no problems runnig behind a DLink Router using my RTL8139 PCmcia Card. But not the same using a NetGear wg511 v2, but this is anoter problem.
I want to connect direct to modem and do a PPPoE conection.
Well, I can setup PPPoE and pon can connect, I can see ppp0 IP, but I cant navigate, cant even ping dns.
DNS´s servers IP were cauch by PPPoe Routine (pri 200.204.0.10 and Sec ...).
Neither Dillo nor Firefox, neither ping to DNS nor traceroute...
Mtu is 1492.
Have a chance to conect directly to ADSL and PPPoE???
Thanks from Brazil,
NettoBr
Posted by NettoBr on Oct. 25 2005,23:03
Hello all people,Solved.
Well, PPPoE routine in DSLPanel doesn't set default gateway correctly.
It sets default gateway to modem, when it should be to ppp0 address recently got
route add default gw pppoe-addr dev ppp0
Please fix this in DSL 2.0 RC2.
Thanks from Brazil, land of beaultiful women and places
NettoBr
Posted by nico_paris on Nov. 01 2005,02:14
I have exactly the same problem, i'll try your solution this evenning after work. thanks! hi from Japan French expat'
Posted by NettoBr on Nov. 01 2005,17:56
Please, Please!Please fix this route in DSL 2.0 RC2.
Someone have or know how to hack US with Deadkeys Keyboard from another linux???
I think its very important to have accents like "ô" in us keyboard.
Thanks from Brazil, land of beaultiful places and women.
NettoBr
Posted by NettoBr on Nov. 01 2005,17:59
Hello Nico_Paris,I think you have to delete wrong route first. I think.
NettoBr
Posted by nico_paris_in_japan on Nov. 02 2005,06:20
ayayaynothing is workin.
Im a rookie on linux. how to delete wrong route first?
then, i tried but didnt work, so, maybe i should explain what i'm doing.
I start DSL. I do first pppoeconf. then pon dsl-provider. but strange, makes like unstable, with interruptions. sometime if i do ifconfig ppp0, says:
ppp0 link encap:Point-Point Protocol
POINT TO POINT NOARP MULTICAST MTU 1500 METRIC=1
Rx packets:0 errors:0 dropped:0 overuns:0 frame:0
Tx packets:0 errors:0 dropped:0 overuns:0 carrier:0
collisions:0 tyxqueuelen:3
Tx bytes:0 (0.0B)
but then i write again then
ifconfig:ppp0:error fletching interface information:Device not found
so i go to edit resolve.conf, replace nameserver with providers (primary and secondary) and same.
so i do poff
it says lots of pppd , so i do poff -a, start again pon dsl-provider, nothing comes. start lots of pon, then as an old engine, so machine starts, it shows flux in full white in the little box in the right (average 180 k/s) so i do ifconfig ppp0, same but MTU (dont know what that) but no interruption problems
ppp0 link encap:Point-Point Protocol
POINT TO POINT NOARP MULTICAST MTU 1454 METRIC=1
Rx packets:0 errors:0 dropped:0 overuns:0 frame:0
Tx packets:0 errors:0 dropped:0 overuns:0 carrier:0
collisions:0 tyxqueuelen:3
Tx bytes:0 (0.0B)
but no internet with firefox...
i tried
route del default
route add default ppp0
but just answers "no such device"...
so, maybe I have to get a clean way to configure it...
Posted by NettoBr on Nov. 03 2005,01:35
Hello Nico_parisI dont know what you did, but I can explain what i have done.
First of all, turn OFF and ON (wait for online Led) your ADSL modem (I think yours is Ethernet connected to your computer, OK?
BOOT DSL and click on DSL control PANEL.
There you can find a PPPOE butom, click on it. The Hot point here is: it must find a concentrator.
Here I answer defalt to all questions except for my autentication data.
if a concentrator is found and your autentication data is correct this is the only thing you have to do to get connected.
I think you are connected now, but cant navigate, see route command output, your defalut gateway is wrong...
Execute these commands:
ifconfig ( to catch PPPOE-ADDR)
route add default gw PPPOE-ADDR dev ppp0
At this time I have 2 default gw routes, but I can navigate, if you cannot navigate delete your wrong route, ask for google the route command format.
BTW, forget about pon and poff, I´m looking for its output as a mad horse. Cant find it anyway. Someone can tell me???
Thats the way I activate my ADSL PPPOE conection on DSL.
Dont work, get an old Pentium 166 or less with 2 network cards, 1 floppy (no HD) install FREESCO.org and you´ll have i nice home gateway firewall to internet. I have one p133 gateway serving 20 PC´s and as RAS too.
Enjoy DSL
Nettobr
Posted by jls legalize on Nov. 03 2005,09:25
with the pirelli alice gate adsl eth modem I have to switch on the modem after dsl is completely started
Posted by nico_paris_jap on Nov. 04 2005,01:49
ok I'll try everything of it
Posted by nico on Nov. 04 2005,05:13
yay ok, i tried the same on ubuntu, then i could do a plog.so it answered me
localhost pppd[xxxxx] ppp session is yyyyy
localhost pppd[xxxxx] using interface ppp0
localhost pppd[xxxxx] connect ppp0 <--->eth0
localhost pppd[xxxxx] couldn't increase MTU to 1500
localhost pppd[xxxxx] couldn't increase MRU to 1500
localhost pppd[xxxxx] couldn't increase MRU to 1500
localhost pppd[xxxxx] CHAP authentication failed:authentication failed
localhost pppd[xxxxx] couldn't increase MTU to 1500
localhost pppd[xxxxx] couldn't increase MRU to 1500
localhost pppd[xxxxx] connection terminated
means authentication looks like failed... but i entered my login and password!!
Posted by nico on Nov. 04 2005,05:18
thats a problem. i asked someone i know to look FAI's web site, said that there is not linux support. something like it can not work with linux... but ethernet modems, always work, no?it's not a pb of password and login, i used it today for paiement registration
)ok,
maybe it's still configuration problem...
i'll look more...
Posted by NettoBr on Nov. 04 2005,11:51
Hello NicoMany providers cannot use 1500 MTU only 14xx (92 if I can remember)
NettoBr