iB::Topic::D-Link DWL-G122 v.A1 problems

	Damn Small Linux :: Damn Small Linux Board The DSL Forums

» Welcome Guest
[ Log In :: Register ]

Damn Small Linux Board » Damn Small Linux » Networking » D-Link DWL-G122 v.A1 problems

		Mini-ITX Boards Sale, Fanless BareBones Mini-ITX, Bootable 1G DSL USBs, 533MHz Fanless PC <-- SALE $200 each!
		Get The Official Damn Small Linux Book. DSL Market , Great VPS hosting provided by Tektonic

Pages: (3) </ 1 [2] 3 >/

[ Track this topic :: Email this topic :: Print this topic ]

Topic: D-Link DWL-G122 v.A1 problems

< Next Oldest | Next Newest >

^thehatsrule^ Offline

Group: Members
Posts: 3275
Joined: July 2006

Posted: Sep. 27 2006,13:32

Hm, according to http://linux-wless.passys.nl/query_part.php?brandname=D-Link its a prism gt, not a prism2 - I must've read a bad post somewhere else. I guess you best bet would be prism54.org

So your usb is detected.. think you can use lsusb -v ?

se2schul

Group: Members
Posts: 15
Joined: Sep. 2006

Posted: Sep. 27 2006,22:20

Quote (^thehatsrule^ @ Sep. 27 2006,09:32)

So your usb is detected.. think you can use lsusb -v ?

0000:00:00.0 Host bridge: Toshiba America Info Systems 601 (rev 27)
Flags: bus master, medium devsel, latency 0

0000:00:02.0 CardBus bridge: Toshiba America Info Systems ToPIC95 (rev 07)
Flags: bus master, slow devsel, latency 0, IRQ 11
Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=14, subordinate=14, sec-latency=0
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff

0000:00:02.1 CardBus bridge: Toshiba America Info Systems ToPIC95 (rev 07)
Flags: bus master, slow devsel, latency 0, IRQ 11
Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=15, subordinate=15, sec-latency=0
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff

0000:00:04.0 VGA compatible controller: Chips and Technologies F65554 (rev c2) (prog-if 00 [VGA])
Flags: stepping, medium devsel
Memory at fe000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=256K]

0000:00:0b.0 USB Controller: NEC Corporation USB (rev 01) (prog-if 10 [OHCI])
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at fdfff000 (32-bit, non-prefetchable) [size=4K]

^thehatsrule^ Offline

Group: Members
Posts: 3275
Joined: July 2006

Posted: Sep. 28 2006,17:21

Err.. I think you did an lspci instead of lsusb (I edited my post earlier) :P

Anyways, I looked it up, and you do have the right model you thought you did.
{USB_DEVICE(0x2001, 0x3703)}, /* DLink DWL-G122 */

And I looked into the forum and official site for prism54, and found out you're better off trying to do your first post (ndiswrapper)... as the driver only supports newer 2.6 kernels, and is incomplete.

roberts

Group: Members
Posts: 4983
Joined: Oct. 2003

Posted: Sep. 28 2006,17:34

When using ndiswrapper you will need both the .inf and the corresponding .sys files. Your first post seemed to indicate that only the .inf file was copied.

se2schul

Group: Members
Posts: 15
Joined: Sep. 2006

Posted: Sep. 29 2006,02:05

Ah... That was one of my mistakes.

Now the driver gets installed.

When I type: "ndiswrapper -m", it says that modprobe config already contains alias directive. I tried to start it using 'modprobe ndiswrapper', but I can't tell if it's working.

I tried to configure it using Netcardconfig, WLanconfig, Ndiswrapper, and IWconfig under the DSL Control Panel, but I can't seem to get it to work.

What should I try next ??

11 replies since Sep. 24 2006,17:14

< Next Oldest | Next Newest >

[ Track this topic :: Email this topic :: Print this topic ]

Pages: (3) </ 1 [2] 3 >/

Damn Small Linux Board » Damn Small Linux » Networking » D-Link DWL-G122 v.A1 problems