|
Title: Tulip driver Post by: jcdq on July 27, 2013, 05:44:56 AM Hi, friends...
Where can I find the tulip driver -if possible version 1.1.15 (feb.27.2007) (or how can I find and run the tulip.o file)? Thanks for any answer.... Title: Re: Tulip driver Post by: CNK on July 28, 2013, 12:17:09 AM The Tulip driver is already in DSL in the directory "/lib/modules/2.4.31/kernel/drivers/net/tulip". It should be loaded automatically. Are you having trouble with your network card?
Modules may be loaded at the terminal using the "modprobe" command. Title: Re: Tulip driver Post by: jcdq on July 28, 2013, 05:32:32 AM Hello CNK...
I `d installed DSL in frugal mode on a eone (emachines) 500 with 191 MB of RAM. eth0---intel DS21145 tulip I tried "modprobe tulip" but when I try to start, it doesn`t work.......................... dsl@box:~$ sudo su [/home/dsl]# modprobe tulip [/home/dsl]# ............. [/home/dsl]# ifconfig eth0 up [/home/dsl]# ifconfig eth0 Link encap:Ethernet HWaddr 00:D0:E8:48:A5:A1 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:32 dropped:0 overruns:0 frame:0 TX packets:0 errors:8 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:9 Base address:0x1000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:73 errors:0 dropped:0 overruns:0 frame:0 TX packets:73 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:40930 (39.9 KiB) TX bytes:40930 (39.9 KiB) ............................................ [/home/dsl]# dmesg cloop: losetup_file: 38 blocks, 65536 bytes/block, largest block is 36338 bytes. ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 2830 blocks, 65536 bytes/block, largest block is 65562 byte s. ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 717 blocks, 65536 bytes/block, largest block is 45242 bytes . ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 645 blocks, 65536 bytes/block, largest block is 60447 bytes . ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 160 blocks, 65536 bytes/block, largest block is 35657 bytes . ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 21 blocks, 65536 bytes/block, largest block is 35965 bytes. ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 179 blocks, 65536 bytes/block, largest block is 37896 bytes . ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 820 blocks, 65536 bytes/block, largest block is 48605 bytes . ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 1416 blocks, 65536 bytes/block, largest block is 65562 byte s. ISO 9660 Extensions: RRIP_1991A usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz> hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended i8253 count too high! resetting.. i8253 count too high! resetting.. eth0: Invalid media table selection 7. 00:13.0: tulip_stop_rxtx() failed 00:13.0: tulip_stop_rxtx() failed 00:13.0: tulip_stop_rxtx() failed etc....... Title: Re: Tulip driver Post by: CNK on July 28, 2013, 01:20:11 PM It looks like the drivers have loaded for your card (otherwise eth0 wouldn't be listed by ifconfig), they just aren't connecting to the net.
You can use the "pump" command to set up the network connection automatically using DHCP. I assume you are connecting to a router, in which case are you sure it can accept connections from new PCs and has DHCP enabled?
Powered by SMF 1.1.20 |
SMF © 2013, Simple Machines
|